Tuesday, April 20, 2010

Cleaning of Isolators and Bio-Safety Cabinets

By: Howard Siegerman and Karen Bonnell
September 2006

Good contamination control practices and adherence to established, written SOPs can minimize cross-contamination in isolators and bio-safety cabinets.
Isolators (Figures 1 and 2) and bio-safety cabinets, also known as “safety cabinets,” “biocontainment isolators,” “containment isolators,” or “barrier isolators” (Figure 3) are well accepted as cost-effective, convenient, and compact controlled environments that provide product and personnel protection. These devices consist of protective enclosures that physically isolate products from the background environment (the room outside the isolator), either because the product of interest is unsafe and therefore needs containment or the product cannot tolerate contamination and therefore needs isolation. Collectively, they are known as “separative enclosures,” or more properly, “separative devices.”
The term “isolator” is usually reserved for pharmaceutical and pharmacy applications, whereas the term “bio-safety cabinet” (BSC) is used in the pharmacy, biotechnology, and microbiology industries. For this discussion, we will consider that isolators and Class II bio-safety cabinets (and associated transfer devices) in biotechnology, microbiology, pharmaceutical and pharmacy applications are used as ISO Class 5 devices in terms of air particle cleanliness and are maintained as sterile environments to a sterility assurance level (SAL) ranging from 10-3to 10-6depending upon application.
Some applications, such as the handling of cyto-toxic drugs, potent hormones, and radiopharma-ceuticals, require both containment and isolation to achieve both protection of personnel from the product and protection of the product from contamination. Brian Midcalf, Chairman of the Pharmaceutical Isolator Working Party and User Group and Assistant PTQA Course Director, University of Leeds, UK, points out that progression from product isolation to product containment to product isolation and containment represents movement along what could be considered the “separation continuum.” These activities would typically be done in a Class II bio-safety cabinet or compounding aseptic containment isolator (CACI) where the necessary levels of air particle control and sterility would be maintained.

Figure 1. Pharmaceutical
Isolator
(Photo courtesy of Getinge,
La Calhene)

Figure 2. Compounding Aseptic
Isolator
(Figure courtesy of NuAire, Inc.)

Figure 3. Bio-safety Cabinet
(Photo courtesy of The Baker Company)
In applications where containment only is required, air flow is directed into the enclosure from the outside environment and filtered air is exhausted. This arrangement would suffice for a Class I bio-safety cabinet. Conversely, where product protection is need, filtered air is delivered to isolators that maintain a net positive pressure to the background environment. This arrangement would suffice for a pharmaceutical isolator or a compounding aseptic isolator in which containment is not required because hazardous products are not involved. Where containment and production protection are required, air flow into and out of the separative enclosure is filtered, using BSCs and CACIs.
In order to maintain product quality and integrity, it is necessary to clean isolators and bio-safety cabinets on a regular basis with appropriate cleaning products according to established and validated standard operating procedures (SOPs). Some isolators can be cleaned with clean-in-place (CIP) systems using spray wands. Others require manual cleaning with wipers, mops, cleaning agents, and if necessary, disinfectants. For the latter category, this article addresses the wipers and mopping systems that are best used for isolators and bio-safety cabinets and provides recommendations on optimum cleaning techniques. The manner in which pharmaceutical isolators, compounding aseptic isolators (CAIs), and bio-safety cabinets are used is sufficiently different that different cleaning (and disinfection) approaches are needed. Suggested protocols and recommended products are provided for the three applications. The reader may also wish to refer to publications dealing with the cleaning of aseptic pharmaceutical environments for additional background information.1-6
Optimum Cleaning Procedures
Cleaning of separative enclosures such as isolators and bio-safety cabinets requires specialized procedures for optimum results — procedures termed as “critical cleaning.” These procedures are counterintuitive and differ from the casual, cursory wiping approach that is used to clean a kitchen counter at home. While old and worn cotton dishtowels (often not replaced for many days) may be used in a circular motion to clean up spills or soils on kitchen countertops, this approach cannot be employed for separative enclosures. Neither the wiping material nor the wiping action would be appropriate for isolators and safety cabinets. The kitchen counter may look clean — in fact, it may appear clean enough to eat on (this probably speaks more to the tolerance of the human body for environmental bacteria than the apparent cleanliness of the counter) — but it is still not clean enough for the contamination requirements of a separative enclosure. Fortunately, several sources7-8 provide guidance for best practices for critical cleaning.
One could well ask, “Why bother with wiping? Why not just spray with alcohol to clean the surface?” The case for wiping as opposed to merely spraying was effectively made by Cockcroft and co-workers 9 who studied disinfection techniques for transfer of components into hospital pharmacy cleanrooms. They stated “…spraying [with alcohol] may reduce the bioburden slightly, but wiping is much more efficient and a combination of spraying and wiping gave the best results.” Further, the following points were made: “If a disinfectant wipe is used, two modes of action come into play. Particles and microorganisms are removed from the surface on to the wipe as the fibers pass over the surface, or the microorganism is killed by the disinfectant. If not killed by the disinfectant, the micro-organisms collected will remain on the wipe unless transferred by contact with another surface such as the hand manipulating the wipe. For this reason, it is recommended that a fresh part of a sterile wipe is used for each wiping action and overlapping strokes are used.”
The wiping action puts the fabric in intimate contact with the surface, allowing the application of strong forces for the removal of contaminants such as bioburden. Wiping has a long and successful history for removal of contaminants from cleanroom surfaces. However, to be successful, the wiper must be used properly. Table 1 addresses the primary concerns in the use of wipers and mops for critical cleaning and provides corresponding best practices with explanations. This information is also summarized in Figure 4.
Concern
Best Practice
Comment
Effective removal of surface soils Select wiping material that entraps soils. Fold wiper in quarters
Use appropriate detergent or other cleaning agent.
Soils are collected in the fabric and discarded with the wiper
Ensures full contact of wiper to surface
Cleaning agent must be compatible with materials of construction used in isolators or safety cabinets
Re-contamination of surfaces already cleaned Select non-linting fabrics
Wipe in linear, overlapping strokes from clean area to dirty area.
Refold wiper to expose fresh wiper surface after each stroke.
Prevents contamination of wiped surface from particles and fibers from wiper fabric
Wipe vertical surfaces from top to bottom. Circular wiping action re-contaminates area just cleaned.
Prevents re-deposition of contaminants picked up on previous stroke.
Deposition of residues from cleaning and disinfecting agents Remove residues with wipers wetted with deionized water or 70% isopropyl alcohol (IPA) solution Ensures that bare surfaces are disinfected and that unsightly residues do not accumulate
Cleaning Effectiveness Surfaces should be free from visible contaminants after cleaning Illuminating surface with high intensity light at an oblique angle will help to identify soils not removed. Examine the last wiper in contact with the surface to verify absence of visual contaminants on the wiper.
Table 1. Critical Cleaning with Wipers and Mops
WIPING GUIDE
  1. Follow relevant site protocol (procedures for safety,contamination,etc.) and wear cleanroom gloves.
  2. Fold wiper in mid-air into quarter folds.
    (Fig 1A-1C) This will produce several clean surface areas and allow better contact with the surface to be wiped.
  3. When wiping,hold the wiper so that the single-fold edge is outward toward the area to be wiped.Hold the selvages closer to your hand.(Fig 2)
  4. Use either a pre-wetted wiper or a dry wiper moistened with an appropriate cleaning agent.
  5. Wipe in one direction, overlapping wiped area by 10% to 25%.Wipe sys-tematically,for example,from top to bottom,far to near.(Fig 2)
  6. Wipe from cleanest to least clean regions of the surface being wiped.
  7. Keep track of which surfaces have been cleaned and which wiper areas are unused.
  8. Use the cleanest surfaces of the wiper. If re-wiping use clean wiper area,not used wiper area.
  9. Dispose of wipers according to site procedures.
Wiping Wet Spills
  1. Identify the spilled liquid.Follow the Material Safety Data Sheet (MSDS).
  2. Choose wiper and gloves that will not be degraded by liquid.
  3. For hazardous spills,wear two pairs of gloves and try to keep the gloves dry.Wear any other necessary protective gear.
  4. Use dry wipers to wipe spills up im-mediately,then wipe slowly.
  5. Dispose of wipers according to site procedures.
Figure 4. Wiping Guide
Cleaning and Disinfection of Pharmaceutical Isolators
Overview
This section deals with the cleaning and disinfection of pharmaceutical isolators used to conduct aseptic filling operations, sterility testing, cell culturing, and purification activities, among others. Later in this article we deal with the cleaning and disinfection of compounding aseptic isolators used by pharmacies. Both types of isolators are rated as ISO Class 5 devices in terms of air particle cleanliness and are maintained as sterile environments to an SAL ranging from 10 -3 to 10-6.
Akers and Agalloco10 have pointed out that there are no substantial differences between an isolator and a cleanroom as far as the cleaning of product contact surfaces are concerned. Obviously, an isolator is smaller in volume than a cleanroom, with a correspondingly smaller footprint. But both need to be cleaned and disinfected and these processes should be thorough, consistent, convenient, and validatable. Previous publications have addressed the general topic of cleaning of isolators.11-16 This section, however, focuses on details such as wiper selection, wiping procedures, protocols and step-by-step guidelines for isolator cleaning. Commercial training programs for isolator cleaning and use are also available.17-18
Wipers and Mops for Cleaning and Disinfection of Isolators
Much of the literature on isolator cleaning refers to the need for “low-linting” fabrics that do not shed. However, little guidance is provided as to which fabric types are best. The lint that is shed from wiping or mopping materials is made up of loose fibers that are not bound to the fabric surface or that are broken free during the cleaning process. Cleaning and disinfecting solutions can promote this linting or shedding activity if inappropriate fabrics are used.
A wide variety of fabrics can be fashioned into wipers or mops for use in cleaning isolators. These include natural materials such as cotton, rayon, and cellulosics, synthetic materials such as polyester, nylon, polypropylene or foams, or blends such as polyester-cellulose combinations. Of these choices, only polyester knit fabrics have the requisite cleanliness, low particle and fiber counts, low endotoxin levels, low extractable residues, durability, and chemical compatibility that are needed for the cleaning and disinfection of isolators. Further, polyester knit fabrics can be sterilized by autoclaving or by gamma irradiation to an SAL of 10-6without loss of structural stability. The characteristically low levels of releasable particles and fibers associated with polyester knit fabrics are especially important in aseptic applications since it is well known that particles are potential carriers of bacteria.11
Put simply, polyester knit fabrics used for wipers and mop covers will not contaminate isolator surfaces when used in cleaning and disinfection operations. Consequently, they represent the best choice for “non-linting” or “non-shedding” materials. The same cannot be said for other fabrics.
Sterile polyester knit wipers are used during production to clean up spills, wipe down gloves (when wetted with sterile 70% IPA), or to provide clean work surfaces. These wipers can be wetted with (i) detergents to clean the isolator, (ii) deionized water or 70% IPA [all IPA solutions described in this article are assumed to be 70% IPA/30% water (v/v), where the “water” is either water for injection (WFI) or deionized water (DIW)] to remove cleaning agent residues, (iii) disinfecting agents to disinfect the isolator, and (iv) deionized water or 70% IPA to remove disinfectant residues. Pre-wetted sterile wipers, containing 70% IPA are also available for these activities. Before IPA solutions are used for cleaning, rinsing, or sanitizing isolator surfaces, ensure that the materials of construction in the isolator will withstand repeated exposure to IPA. Some transparent materials, for example poly-carbonates, may cloud over or crack when exposed to IPA.
Cleaning and Disinfecting Frequency
Good contamination control practice would suggest that isolators and associated transfer devices be cleaned and disinfected after a production campaign, (a session in which multiple products of the same type are manufactured) has been concluded (referred to here as “post cleaning” which includes disinfection) and again before a new production campaign is begun (referred to here as “pre-cleaning” which also includes disinfection). This will avoid cross contamination. If the isolator has not been opened after “post cleaning” and if a new manufacturing campaign starts within short time (say one hour) after “post cleaning,” then an additional “pre-cleaning” step may be unnecessary. In that case, a surface sanitiza-tion of the isolator interior with sterile wipers and/or mops wetted with sterile 70% IPA may be sufficient to ready the isolator for production. Decisions on cleaning/disinfecting frequency and procedures are the province of the Quality Supervisor.
Cleaning and Disinfecting Specifics
Since the isolator is most often cleaned and disinfected while closed, to maintain the sterility of the isolator, sterile cleaning and disinfecting consumables — wipers, pre-wetted wipers, mops, cleaning/disinfecting agents, water, 70% IPA, etc. — must be introduced through an appropriate transfer device. Even if a facility’s SOP calls for the isolator to be opened for cleaning and disinfection, the use of sterile wipers and pre-wetted wipers is recommended, since they can be introduced into the isolator for in situ cleaning needs. This also eliminates the confusion of having both sterile and non-sterile wipers on hand and eliminates the need to sterilize wipers prior to use within the isolator.
The usual sequence for cleaning and disinfection includes a cleaning step, a rinsing step, a disinfecting step, another rinsing step, and if needed, a gaseous sterilization step, and a cleaning validation step. As a side note, wipers can be used to wipe down any hard surface articles that are introduced into the transfer device for use within the isolator. This will remove surface contaminants that might otherwise compromise disinfection or sporicidal treatments.
Cleaning
To ensure that each production run will be conducted in a pristine environment, it is necessary to clean the isolator to remove any residues and soils produced from the prior run. These contaminants, if not removed, would otherwise unnecessarily consume disinfectant and mitigate its application.19
Typically, small flat surface mops known as isolator cleaning tools (Figure 5), wipers, swabs, and detergents are most commonly employed for these cleaning applications. Detergent selection is based on the type of soil to be removed. Also, cleaning mechanism factors such as wetting, dissolution, oxidation, hydrolysis, enzyme action, emulsification, deflocculation, sequestration, saponification, and rin-seability can all be important in determining which detergent to use.20-21 The detergent is applied to the surface in the manner described in Optimum Cleaning Procedures, using quarter-folded wipers with linear overlapping strokes, wiping from clean areas to dirty, and renewing the wiper surface after each stroke. Wipers are used for all surfaces within arm’s reach. Isolator cleaning tools are used for surfaces beyond arm’s reach.
Detergents also have the benefit of reducing the bioburden level on the surface; this lessens the task somewhat for the subsequent disinfection step.

Figure 5 – Isolator cleaning tool
in use
(Photo courtesy of Getinge, La
Calhene)
Rinsing Following Cleaning
After cleaning, detergent residues are removed from the surfaces with wipers or mops that have been wetted with sterile deionized water or sterile 70% IPA. This will ensure that disinfectants have the opportunity to contact bare surfaces. Surfaces are considered clean when devoid of visible surface contaminants. Verify visually that the last wiper used to wipe down the surface is also devoid of visible residues.
Disinfection
The same procedures are followed for disinfection, except that liquid disinfecting agents are substituted for detergents. Disinfecting agents can include phenolics and quaternary ammonium compounds (use pheno-lics or quats, never both together). Aqueous mixtures of IPA will provide some measure of disinfection, but they are ineffective against spores. Occasionally, liquid sterilants such as sodium hypochlorite (bleach), per-acetic acid, and hydrogen peroxide will be substituted for disinfectants when sporicidal activity is needed. These sterilants can be corrosive to surfaces and are therefore used intermittently.
Rinsing Following Disinfection
The same procedure is followed here as in rinsing following cleaning. Disinfecting agent residues are wiped from the surface with wipers or isolator cleaning tools that have been wetted with sterile deionized water or sterile 70% IPA. This will eliminate the buildup of residue deposits that become difficult to remove in subsequent cleaning operations, and that will cause staining of work surfaces.
Gaseous Sterilization 22
Once the cleaning and disinfection steps are completed, if required, the isolator can be sterilized, with a suitable sterilant such as Vaporized Hydrogen Peroxide (VHP).
Cleaning Validation
Surface sampling with swabs to verify the absence of cleaning and disinfecting agents may be required after rinsing. More details can be found in other documents.2, 23-25 This constitutes the “post clean” described in the cleaning frequency section above. An identical series of steps would be followed for a “pre clean” operation, except that if surfaces have not been contaminated since the “post clean,” only disinfection, rinsing, and perhaps gaseous sterilization may be needed. Again, the Quality Supervisor determines what cleaning and disinfecting steps are required for any given circumstance.
Recommended Products
Table 2 lists the various cleaning tasks and the products recommended for both pharmaceutical isolators and compounding isolators, since so many of the tasks are common to both.
Cleaning Task
Recommended Products
Post-clean or pre-clean of interior walls, ceiling and deck of closed isolators Choose one or more of the following:
  1. Isolator cleaning tool with polyester knit mop covers to reach all interior surfaces of the isolator. Sterilize the cleaning tool and mop covers before introducing them into the isolator. Dampen the mop covers with sterile WFI, sterile DIW, sterile IPA, [again IPA refers to 70% IPA, 30% DIW (v/v)], detergent cleaning solution, disinfectant solution, or liquid steri-lant as described in cleaning and disinfecting specifics.
  2. Sterile IPA-prewetted polyester knit wipers.
  3. Sterile dry polyester knit wipers. Dampen the wipers with the solutions described in 1 above, as appropriate for the cleaning task at hand.
  4. Swabs with polyester knit heads for cleaning hard-to-reach spaces, crevices, nooks, crannies, and isolator corners. These swabs can be dampened with one of the solutions described in 1 above.
Wiping down deck between compound sterile preparations Sterile IPA-prewetted polyester knit wipers.
Cleaning up spills while isolator is in use Sterile dry polyester knit wipers for absorbing spilled liquid, then Sterile IPA-prewetted polyester knit wipers for removing surface contamination.
Wiping down gloves while isolator is in use Sterile IPA-prewetted polyester knit wipers.
Wiping mating and sealing surfaces between transfer isolator(s) and main isolator Sterile IPA-prewetted polyester knit wipers.
Wiping down articles before placing them in the transfer isolator Sterile IPA-prewetted polyester knit wipers.
Validation of isolator cleaning Total Organic Carbon (TOC) Cleaning Validation kit.
Cleaning Background Environments Flat surface mop with polyester knit mop covers, wetted with detergent cleaning agents, disinfectants and deionized water as described in Cleaning and Disinfection of Compounding Aseptic Isolators
Table 2. Cleaning Tasks for Pharmaceutical Isolators and Compounding Aseptic Isolators Text in black refers to tasks for both pharmaceutical isolators and compounding aseptic isolators. Text in blue refers to tasks unique to pharmaceutical isolators. Text in red refers to tasks unique to compounding aseptic isolators.
Cleaning and Disinfection of Compounding Aseptic Isolators (CAIs)
Overview
This section deals with the cleaning of isolators used in hospital pharmacies and other dispensing facilities to formulate (i.e. “compound”) individual prescriptions for patient care. As for pharmaceutical isolators, CAIs are rated as ISO Class 5 devices in terms of air particle cleanliness and are maintained as sterile environments to an SAL of 10-3. In the United States, the cleaning and disinfecting of CAIs and the associated background environments fall within the province of the U.S. Pharma-copeia’s document USP <797>.12 CAIs are not used in exactly the same manner as the isolators used for pharmaceutical manufacturing. There are few opportunities to run extensive production campaigns with CAIs. A licensed compounding facility producing cancer treatment drugs, for example, may produce batches of identical products numbering in the tens or low hundreds, but a typical hospital pharmacy is more likely to have a “manufacturing run” of just a single preparation (or perhaps a few doses of the same drug), transferred aseptically into a vial, intravenous (IV) bag, syringe, infusion device, etc. These are termed compound sterile preparations (CSPs) in the industry. While the extensive cleaning and disinfection procedures previously described for pharmaceutical isolators are unnecessary and obviously impractical here, some form of cleaning and surface saniti-zation of compounding isolators will be required to prevent cross-contamination.
The cleaning and disinfection activities for CAIs will be separated into three areas:
  • Cleaning and disinfecting the CAI at the beginning of each shift
  • Cleaning and sanitizing the interior of the CAI between CSPs
  • Cleaning the background environment.
At the outset, and to state the obvious, it must be emphasized that any cleaning, sanitizing, disinfection, or sterilization procedures must never be done while compounding activities are underway.
Many of the guidelines for cleaning and disinfection of pharmaceutical isolators, apply here as well. To save space, only specifics that are unique to CAIs will be covered below.
Selection of Wipers and Mop Covers
From a best practice viewpoint, knit polyester wipers and mop covers are again preferred for their low particle and fiber release characteristics for use in these ISO Class 5 isolators. It is recognized that some facilities will consider that blended fabrics of polyester-cellulose (discussed later) may suffice for CAIs. If such fabrics are used within the isolator, the pharmacist should recognize that they do carry a risk of higher particle and fiber release onto the isolator surfaces.
Cleaning and Disinfecting the CAI at the Beginning of Each Shift
The procedures here are identical to what is done for pharmaceutical isolators.
Cleaning and Sanitizing the Interior of the CAI between CSPs
To avoid cross-contamination between CSPs, the accepted procedure is to wipe the counter or “deck” of the isolator with a wiper wetted with 70% IPA. Pre-wetted wipers are most convenient for this task. This will remove any residues from the work surface and will provide a measure of surface sanitization as well. IPA is a versatile cleaning agent and will remove many different types of soils. Some residues may only be water soluble, so in those cases, wipers wetted with water for injection (WFI) should be used to remove the surface soils. A final wipedown with IPA will leave the surface clean for the next CSP. A second IPA-wetted wiper should be used to wipe down the gloves to guard against cross-contamination in the preparation of the next CSP.
If the CAI is used for compounding hazardous drugs, then swab sampling of the interior surfaces with subsequent analysis may be appropriate to prove that the compound of interest is not present at levels which would constitute an exposure limit danger.
Cleaning and Disinfection of Background Environments
The USP <797> document requires that floors in the background environment (also termed “buffer or clean area”) be mopped daily, while walls, ceilings, and shelving are to be mopped monthly. To accomplish these tasks most effectively, the following procedure, utilizing a single flat mop with replacement mop covers can be employed.
1. Place a clean dry mop cover on the mop head and wet it with a suitable liquid cleaning agent – either detergent or 70% IPA – to clean the ceilings, walls, and floors of the background environment. Use linear, overlapping strokes to ensure all surfaces are cleaned thoroughly (Figure 6). If the mop cover becomes visibly dirty during the cleaning process, replace it.
2. If 70% IPA was used in step 1 proceed directly to step 3. If a detergent was used, place a clean mop cover on the mop head, then dampen it with either deionized water or 70% IPA. Use linear, overlapping strokes to remove the dried cleaning agent residue. Again, if the mop cover becomes visibly dirty during the cleaning process, replace it.
3. Place a clean mop cover on the mop head and spray the mop cover with an approved disinfectant (e.g., phenolic or quaternary ammonium compound) solution. Spread the disinfectant over the ceiling, walls, and floors with linear, overlapping strokes. Alternatively, spray the ceilings, walls, and floors with the disinfectant and spread the disinfectant solution evenly over the surfaces with the mop. Allow appropriate kill time (e.g., 10 – 20 minutes) for the disinfectant to do its job.
4. Place a clean mop cover on the mop head, then dampen it with either deionized water or 70% IPA.
Use linear, overlapping strokes to remove the dried disinfecting agent residue. Again, if the mop cover becomes visibly dirty during the cleaning process, replace it.
This procedure will ensure that the background environment outside the compounding isolator will meet the requirements for USP <797>.

Figure 6 – Flat surface mop for
ceiling, wall, and floor cleaning
Recommended Products
Refer to Table 2 for the various cleaning tasks and the associated products recommended for CAIs. Ignore the blue text in Table 2 which refers to tasks unique to pharmaceutical isolators. Tasks relevant to CAIs are in black and red.
Cleaning Bio-safety Cabinets
Overview
As stated previously, bio-safety cabinets are used to protect operators from the hazardous materials within the cabinet. Class II bio-safety cabinets (used for handling cytotoxic drugs, potent hormones, active pharmaceutical ingredients, etc.) and CACIs that are maintained sterile with ISO Class 5 air particle levels, would be cleaned according to the guidelines laid out previously for pharmaceutical isolators or compounding aseptic isolators. These cabinets require the use of polyester knit fabrics to maintain the necessary particle levels within the separative enclosure.
However, some bio-safety cabinets, such as the Class I category, do not require that the interior of the separative enclosure be kept sterile, do not require that ISO Class 5 air quality be maintained and typically do not incorporate glove ports. For these applications, fabric selection for wipers and mop covers can be relaxed somewhat.
Selection of Wipers and Mop Covers
The blended polyester-cellulose materials that were previously considered too contaminating for pharmaceutical and compounding isolators will be quite suitable for most Class I bio-safety cabinet applications.
Cleaning Specifics for Class I Bio-safety Cabinets
The cleaning specifics for Class I bio-safety cabinets are similar to those for pharmaceutical isolators, except that cleaning activity can be confined to the end of a manufacturing campaign and sterile consumables need not be used. Again, the desire is to prevent cross-contamination from one manufactured product to another. However, since there is no need to maintain sterility, one can reasonably assume that if the bio-safety cabinet interior is cleaned thoroughly and is validated, there should be no need to clean again prior to the beginning of the next manufacturing campaign. These are broad guidelines however, and the protocols defined by the Quality Supervisor must be observed.
One further cleaning activity bears mention. Since the production activity involves hazardous materials, it may be prudent to wipe down the exterior of the manufactured product to ensure that dangerous substances are removed prior to the product being transferred out of the bio-safety cabinet. These wipers, and those used to clean the interior of the bio-safety cabinet, must be appropriately bagged and transferred out of the separative enclosure in a safe manner.
The wipedown procedures follow the same procedures as described in the “Optimum Cleaning Procedures” section. Using linear wiping patterns from clean to dirty (usually top to bottom, front to back), with overlapping strokes, quarter-folding the wiper after each stroke. Since hazardous materials are being removed from surfaces, consideration should be given to changing the wipers frequently. After cleaning, suitable validation tests should be run to verify the absence of the hazardous material involved. Obviously, the bio-safety cabinet must be thoroughly wiped down and decontamination procedure verified before the enclosure is opened to the background environment.
Recommended Products
Table 3 lists the various cleaning tasks and the products recommended for BSCs.
Cleaning Task
Recommended Products
Cleaning of interior walls, ceiling, and deck of closed BSCs at the beginning of each shift Choose one or more of the following:
  1. Isolator cleaning tool with blended polyester-cellulose mop covers to reach all interior surfaces of the isolator. Dampen the mop covers with DIW, IPA, detergent cleaning solution, disinfectant solution or liquid sterilant.
  2. IPA-prewetted blended polyester-cellulose wipers.
  3. Dry blended polyester-cellulose wipers, wetted with the solutions described in 1 above, as appropriate for the cleaning task at hand.
  4. Polyurethane foam swabs for cleaning hard-to-reach spaces, crevices, nooks, crannies, and BSC corners. The swab can be dampened with one of the solutions described in 1 above.
Cleaning up spills while BSC is in use Dry blended polyester-cellulose wipers for absorbing spilled liquid, then IPA-prewetted, blended polyester-cellulose wipers for removing surface contamination.
Wiping down gloves while BSC is in use IPA-prewetted, blended polyester-cellulose wipers.
Wiping mating and sealing surfaces to BSC IPA-prewetted, blended polyester-cellulose wipers.
Wiping down articles before placing them in the transfer device IPA-prewetted, blended polyester-cellulose wipers.
Wiping down manufactured articles before transferring them out of the BSC IPA-prewetted, blended polyester-cellulose wipers.
Table 3. Cleaning Tasks for BSCs
Summary
The manner in which pharmaceutical isolators, compounding aseptic isolators and bio-safety cabinets are used dictate the somewhat varied approach to cleaning and where applicable, disinfection practices. Good contamination control practices and dedicated adherence to established, written SOPs will minimize cross-contamination surprises.
Acknowledgements
The authors wish to thank Brian Midcalf at University of Leeds, Eric Kastango at Clinical IQ, and Scott Christensen and Bill Peters at NuAire for their review of the manuscript and for providing helpful comments. Details on isolator construction and usage were also supplied by Craig Johnson of CPS Pharma and Patrice Cloue of La Calhene.
References
  1. D. Cooper. “Cleaning Aseptic Fill Areas,” Pharmaceutical Technology, (February, 1996).
  2. D. Cooper. “Cleaning, Validating and Monitoring Aseptic Fill Areas,” Pharmaceutical Technology Asia, (September/October, 1997).
  3. D. Cooper. “Sterile Disposables For Maintaining Aseptic Areas,” Pharmaceutical Processing, Vol. 14, No. 8, (August, 1997).
  4. D. Cooper. “Comparing Foam and Fabric Wipers for Applying Disinfectants,” Pharmaceutical Technology, (October, 1998).
  5. D. Cooper. “Applying a Uniform Layer of Disinfectant by Wiping,” PDA Journal of Pharmaceutical Science and Technology, Vol. 54, No. 1, (January/February, 2000) p. 45.
  6. H. Siegerman. “Optimum Wiper Characteristics for the Cleaning and Disinfection of Pharmaceutical Cleanrooms,” R3 Nordic Conference, Tampere, Finland, (May, 2006).
  7. “Standard Practice for Cleaning and Maintaining Controlled Areas and Clean Rooms,” ASTM E2042-04, ASTM International, West Conshohocken, PA, (2004).
  8. “Cleanroom Housekeeping - Operating and Monitoring Procedures,” Document IES-RP-CC018.3, Institute of Environmental Science and Technology, Rolling Meadows IL.
  9. M.G. Cockcroft et al., “Validation of liquid disinfection techniques for transfer of components into hospital pharmacy cleanrooms,” Hospital Pharmacy, Vol. 8, (2001) p.226. http://www.pjonline.com/pdf/hp/200109/hp_200109_paper.pdf.
  10. J. Akers, J. Agalloco. “Isolator Cleaning and Cleaning Validation,” PDA Isolator Conference, (2002).
  11. “Guidance for Industry: Sterile Drug Products Produced by Aseptic Processing,” FDA, (September, 2004), http://www.fda.gov/cder/guidance/index.htm.
  12. (USP) General Chapter <797> Pharmaceutical Compounding—Sterile Preparations, U.S. Pharmacopeia, Rockville, MD; see also proposed revisions issued May 2006 at http://www.usp.org/pdf/EN/ USPNF/PF797.pdf
  13. K. Rossington, “Cleaning of Isolators – a Vital Part of a Contamination Control Program,” Controlled Environments Magazine (formerly A2C2), (April, 2004), http://www.cemag.us/articles.asp?pid=434; “Contamination Control”, Manufacturing Chemist, April 12, 2003,
    http://www.manufacturing-chemist.info/ story.asp?storyCode=20245
  14. “Pharmaceutical Isolators,” Chapter 6, edited by B. Midcalf et al., Pharmaceutical Press, London, (2004).
  15. D. Liberman. et al. “Barrier Isolation Technology: A Safe and Effective Solution for Providing Pharmaceutical Development Facilities,” Pharmaceutical Engineering, (July/August, 2001),
    http://www.mic4.com/articles/safe-and-effective.php.
  16. K. Avis. “Assuring the Quality of Pharmacy-Prepared Sterile Products,”
    http:// www.mic4.com/articles/assuring.php.
  17. “Cleaning and Disinfection of Pharmacy Controlled Environments,” Clinical IQ LLC, Florham Park, NJ.
  18. “Aseptic Training and Validation System,” Valiteq Inc., Cumberland, WI.
  19. H. Siegerman. “Wiping Surfaces Clean,” Vicon Publishing, Amherst, NH, (2004).
  20. D. LeBlanc et al. “Cleaning Technology for Pharmaceutical Manufacturing,” Pharmaceutical Technology, (October, 1993).
  21. M. McLaughlin. “Selecting and Validating Aqueous Detergents,” Controlled Environments Magazine (formerly A2C2), (May, 1999).
  22. A. Booth. “Sterilization Validation of an Isolator System,” Medical Device and Diagnostics Industry, (May, 1999), http://www.devicelink.com/mddi/archive/ 99/05/013.html.
  23. K. Miscioscio. “Choosing the Correct Swab for Cleaning Validation,” Clean-rooms, (January, 1997).
  24. D. Cooper. “Using Swabs for Cleaning Validation: A Review,” Cleaning Validation: An Exclusive Publication, Institute of Validation Technology, Royal Palm Beach FL. (July, 1976) p. 74.
  25. H. Siegerman. “How to Succeed in the Search for Nothing,” Steril Technik, (April, 2006).
Howard Siegerman is Director of Technology for ITW Texwipe,concentrating on contamination control in the electronic and life science markets.He earned B.Sc.,M.A.,and Ph.D. degrees in analytical chemistry from the University of Toronto. Dr.Siegerman holds two patents and has authored a number of technical publications. He can be reached at 201-684-1800 x 220 or hsiegerman@texwipe.com

Karen Bonnell is a Product Manager for ITW Texwipe.She manages the mop line of cleanroom consumables,including mops, pre-wetted and dry mop covers,and isolator cleaning tools.Ms.Bonnell received an M.A.in Biochemistry from Temple University and a B.A.in Biology from Bryn Mawr College.She can be reached at 201-684-1800 x 318 or kbonnell@texwipe.com.

13 comments:

Unknown said...

Getting fire safety cabinets is an important step toward preventing industrial fires. However, it's not the only step. You also need to store the liquids in special approved safety cans. Only then, as the next step, store the cans in the cabinets for added safety.

0s0-Pa said...

There are some good ideas here that I can probably apply to my next construction site cleanup project. Thanks for sharing!

Unknown said...

Thanks for sharing this informative post! Getting fire safety cabinets is an important way to prevent unprotected chemical fires at home and workplace.
http://www.firecabinetsdirect.ie/

alfarida.net@gmail.com said...


شركة مكافحة النمل الاسود بالطائف
شركة مكافحة النمل الابيض بالطائف
شركة مكافحة الفئران بالطائف
شركة مكافحة الصراصير بالطائف
شركة مكافحة البق بالطائف
شركة مكافحة العتة بالطائف

شركات مكافحة الحشرات فى الطائف

رش حشرات بالطائف
ارقام شركات مكافحة الحشرات بالطائف
افضل شركة مكافحة حشرات وفئران



شركة تنظيف بالطائف
شركة تنظيف بيوت بالطائف
شركة تنظيف شقق بالطائف
شركة تنظيف منازل بالطائف
شركة تنظيف فلل بالطائف
شركة تنظيف مفروشات بالطائف
شركة تنظيف بالبخار بالطائف
شركة تنظيف مجالس بالبخار بالطائف
شركة تنظيف خزانات بالطائف
تنظيف خزانات فى الطائف
تنظيف خزانات بالطائف

alfarida.net@gmail.com said...

شركة تنظيف بجدة
شركة غسيل بالبخار بجدة
شركة تنظيف شقق بجدة

شركة غسيل بالبخار بمكة
شركة تنظيف شقق بمكة
شركة تنظيف خزانات بمكة
شركة تنظيف بمكة
شركة مكافحة فئران بجدة
شركة النمل الابيض بجدة
شركة مكافحة البق بجدة
شركة النمل الابيض بمكة
شركة مكافحة البق بمكة
شركة مكافحة حشرات بمكة
شركة مكافحة فئران بالطائف

alfarida.net@gmail.com said...

تنظيف الموكيت فى مكانه
شركة تنظيف سجاد بالرياض
شركة تنظيف موكيت شمال الرياض
شركة تنظيف سجاد بالبخار

شركة تنظيف مجالس بالرياض
شركة غسيل مجالس بالرياض
شركة غسيل كنب بالرياض
شركة نقل اثاث بالرياض 300 ريال
شركة نقل اثاث بالرياض عمالة فليبنية
شركة نقل عفش بالرياض رخيصة
شركة نقل عفش بالرياض

alfarida.net@gmail.com said...

شركة نقل عفش بالمدينة المنورة
شركة نقل اثاث بالمدينة المنورة
شركة تنظيف شقق بالمدينة المنورة
شركة تنظيف منازل بالمدينة المنورة
افضل شركة تنظيف منازل بالمدينة المنورة
شركة تنظيف عمائر بالمدينة المنورة
شركة تنظيف خزانات بالمدينة المنورة
شركة غسيل خزانات بالمدينة المنورة
شركة عزل خزانات بالمدينة المنورة
شركة كشف تسربات المياه بالمدينة المنورة

شركة رش مبيدات فى المدينة المنورة
شركة تنظيف مكيفات بالمدينة المنورة
فنى تركيب مكيفات بالمدينة المنورة

Anonymous said...

Thank you for sharing this.
visit mkprecision.net for more details.

Emily Wonder said...

My daughter (Annabel) suffered from schizophrenia for 5 years. I had no idea what was happening and didn’t know where to turn for help. It was hard then because I really didn’t understand the symptoms earlier until she was diagnosed. There was a time she decided to get away from everyone, I was not excluded. I had to sit and cry almost every day because I felt helpless as a single mother (she is all I have got). The anguish I went through taking care of her alone is beyond explanation because there was no support whatsoever from the dad or family members. I fought for proper medical care and humane treatment; I did everything within my reach to get her cured but all to no avail. Countless different medications was prescribed (Zyprexa, fluphenazine, Risperdal, quetiapine, etc.) that she was taking but all we could get was myriad of side effects such as rigidity, drowsiness, dizziness, tremors and restlessness which tends to worsen the already damaged situation. Frustration was the order of the day. I wrote a couple of messages to the Ontario Mental Health Foundation for help because watching my daughter go through such was devastating. It was at this foundation someone shared a testimony about DR James herbal mix medicine, how effective it is and how she went through the most difficult times of her life trying to help her mom fight Schizophrenia. Being that I was already at the verge of giving up because I just couldn't imagine waking up every morning to fight the same demons that left me so tired the night before. I had to contact the Great  doctor, on his email  (GREATCUREMAN@GMAIL.COM)  from our conversations; I was relieved and convinced that the result is going to be positive because I was made to contact people with worse cases. Today, the awful situation of my daughter has gone by. Her happy life is back. She is now a schizophrenia survivor, and I am glad because my daily routine activities can now kick off without obstructions. Don't let Schizophrenia hinder you from living a desired life and also, never allow anyone to decide for you especially when they don't know what you have to go through to get to where you are. I was almost discouraged by the doctor but then, I remembered that: I have to shield my daughter’s destiny with courage, faith and perseverance because she is not in her right state of mind and that the bravery and freedom from fear is found in the ‘doing’. Her life is now a testimony. After my daughter got cured, from the herbal mix medicine Dr James prepared and sent to me, she said, Mom “I just thought, ‘Well, I’m a weirdo, I’ll never be normal, then I said, my daughter, life itself is a misery, and we get stronger in the places we have been broken. Thanks to you Dr. James  for your excellent counseling, no more psychotic symptoms for the past 3 years and 4 months now. To know more about Dr. James and the effectiveness of his Herbs and roots extracts, and he said he got cures for diseases like Bipolar, DIABETES, HPV, SHINGLES, CANCER, ALS, HEPATITIS B, KIDNEY DISEASE, HERPES, Ovarian Cancer, Pancreatic cancers, Bladder cancer, skin cancer, Prostate cancer, Glaucoma., Cataracts, Macular degeneration, Cardiovascular disease, Autism, Lung disease. Enlarged prostate, Osteoporosis. Alzheimer's disease, psoriasis, Tach Diseases, Lupus, Dementia. Kidney cancer, lung cancer. You can reach the Great Doctor on his Email at ... GREATCUREMAN@GMAIL.COM.  I believe you will testify just like me. INFO @ DrJAMESHERBALMIX@GMAIL.COM.

Kewaunee Labway India Pvt Ltd said...

Hello, really liked your page. Thanks for the post. I Really Found this topic very interesting and useful.

If you want to know more about the Safety Cabinet, please visit our website:

danish said...

I Like to add one more important thing here, The Pharmaceutical Isolator Market is expected to be around US$ 40 billion by 2025 at a CAGR of 8% in the given forecast period.

Navco said...

Excellence post.Thanks for sharing
Best glove manufacturers in India

Glasgow Cleaning Specialists said...

Glasgow Cleaning Specialist Company provides professional one off deep cleans and a bespoke one off Deep Cleaning Service. Our deep cleaning specification takes care of meticulous attention to detail to give you the exceptional results you need

Pharmaceutical Validation Documentation Requirements

Pharmaceutical validation is a critical process that ensures that pharmaceutical products meet the desired quality standards and are safe fo...